About Company

Nairi-Tech is a high-tech company that provides system-level engineering services. The company's main focus is the design and development of specialized automatic testing systems, along with education & research laboratory facilities. Our mission is to meet and exceed our customers' expectations by offering quality products and solutions with the shortest possible turnover time, using the full potential of our highly qualified and certified specialists.

For many years, Nairi-Tech has held the status of a silver alliance partner of National Instruments and for our developments we mainly use the latter's high-tech hardware and software platforms.

Solutions

Li-ion Battery Production Line Automation Using Machine Vision Systems

The system has been designed for monitoring of application process of graphene on cathodic and anodic plate in manufacturing of lithium-ion (Li-ion) batteries.

Distributed SCADA System for Monitoring of Alternative Energy Sources

The distributed SCADA system is intended for data acquisition and control of alternative energy sources. The system is distributed in two buildings, connected by a wireless link.

High-Speed ADCs Automated Testing Equipment                                                                                       

The system is intended for automation of high-speed pipelined ADCs testing process. The current system allows testing of ADCs with sampling rate up to 100MHz, resolution 12 bit and with parallel digital output interface.

Automated Testing Equipment for Wiring Harnesses

The automated testing equipment for wiring harnesses is intended for testing different types of wiring harness. The system allows to test wiring harnesses with wire quantity up to 1024 in order to detect short circuits, broken wires and defective insulation.

Automated Testing Equipment for Current Sensor Chips

The system allows testing of 72 special current chips in parallel. The special software along with FPGA based reconfigurable PXI board and programmable power supply allows testing of UUTs in fully automated mode.

Automated Testing Stand for High Pressure Pipes                                  

The stand is intended for testing high pressure hydraulic pipes in autonomous mode. It has a special chamber for testing providing maximum safety for an operator.

Stand Automation for Processes Simulation Occurring in Oil Wells                                          

The processes simulation stand automation system is intended to create the most reproducible, as well as flexible regulated and precisely maintained conditions for conducting in an automatic mode experiments to study the noise of fluid filtration through a porous medium.

Stand Automation for Processes Simulation Occurring in Injection and Production Wells                         

The processes simulation stand automation system is intended to optimize of the experimentation in the automatic mode to study production and injection wells, as well as to reduce the labor intensity of experiments and increase the accuracy of the plant operating parameters.

Automated Process Control System for Chemical Industry                                                                    

APCS

Automated Process Control System is designed for continuous monitoring and indicating of liquid level in tanks, as well as for monitoring of pumps motors state. All processes are performed by the system in real-time mode.

Data Acquisition System for Metallurgical Production

Data acquisition system is designed to collect and register data from various types of temperature sensors. The system is based on two Ethernet-based data acquisition modules: a 2.4 GHz IoT wireless I/O module and a 16-bit analog differential input module with programmable input ranges on all channels.

   

Products

 

Robotics Lab                                             

 

The Robotics Lab is a mobile robot with omnidirectional wheels. The platform is equipped with a set of sensors and a manipulator with 4 degrees of freedom.

Robotics Educational and Research Platform

The Robotics Educational and Research Platform has been designed as a bench for practical experiments and as an open platform for robotics algorithms design and development.

Mobile Robot for Study of Robotics Systems in Agriculture 

The Mobile Robot test bench has been designed for robotics experiments in the agricultural field.

Automated Wind Tunnel                            

The automated wind tunnel test bench has been designed based on the Flotek or Aerolab wind tunnels. It can be used as a research bench as well as an educational laboratory.

Automated Educational Medium Wind Tunnel             

Automated Educational Wind Tunnel (MINI)

The automated educational medium wind tunnel is an accostable scientific and research laboratory bench. Due to its affordability, the medium wind tunnel makes it possible to duplicate tests performed with the use of more expensive large-scale wind tunnels.

Automated Educational Mini Wind Tunnel              

Automated Educational Wind Tunnel (MINI)

The automated educational mini wind tunnel is an accostable scientific and research laboratory bench. The system consists of different modules for taking measurement from the sensors as well, as controlling the air flow speed in the test section of the wind tunnel.

Information Input and Output Devices Lab                                                

I/O Devices

The Information Input and Output Devices Lab has been designed as a laboratory platform for familiarization with a basic devices applied for information input and output.

Manipulator and Vision Systems Usage in Industrial Automation Lab                                                                                                                        

The educational lab is intended for studying the possibilities of using manipulator and vision systems in industrial automation. Manipulator with 4 degrees of freedom (DOF), color camera, illuminator and a digital weigh scale are used in the lab.

Virtual Control and Research System of Gas Turbine Engine Characteristics

Industrial Data Logger

The Virtual System of Gas Turbine Engine Lab is designed for simulation operation of gas-turbine engines and studying the change in the parameters depending on the engine power conditions.

Laboratory Bench for Study of Gas Turbine Engines Characteristics                            

The lab stand is based on the TurboGen gas turbine electric power generation system by Turbine Technologies, equipped with National Instruments control and measurement hardware.

Research Lab for Studying Solar Cells' Parameters and Characteristic   

The laboratory stand is designed for studying physical processes of solar and light emission conversion into electrical energy. The lab stand allows students to gain practical skills in working with solar cells and explore their main parameters and characteristics.

Automated Airfoils Deformation Research Lab                   

Strain Analysis System for Airfoils

The automated educational stand for the study of airfoils deformation has been developed based on the TrueStructure bench by Turbine Technologies.

Tethered Power System for Unmanned Aerial Vehicles

Remote_Control

Tethered Power System is intended to provide unlimited power from a ground power source of an unmanned aerial vehicle. The system provides continuous operation of the UAV in the flight mode for an unlimited time at a distance of up to 100 meters.

Electric Equipment Remote Control System 

Remote_Control

The system has been designed for autonomous remote control and monitoring of electrical equipment according to a predetermined schedule.

Automated Testing Equipment for Wiring Harnesses

The automated testing equipment for wiring harnesses is intended for testing different types of wiring harness. The system allows to test wiring harnesses with wire quantity up to 1024 in order to detect short circuits, broken wires and defective insulation.

Industrial Data Logger                                                                  

Industrial Data Logger

The Industrial Data Logger is intended for data acquisition and logging from different types of analog and digital input modules.

Flight Parameter Logger                      

Flight parameter logger is intended for parameters measurement and logging from different types of sensors.

Pressure Sensors Arrays          

Pressure sensors’ array (PSA) is the digital version of traditional fluid-filled multitube manometers. It is intended for use in wide range of areas where it’s required to simultaneously measure pressure in multiple channels. There are currently two modifications of pressure sensors’ array 8 and 24 channels.

Automated Testing Equipment for PCBs Functional Testing

The system has been designed and developed for automated testing of PCBs assemblies functionality.

TB-RJ45-4330 Terminal Block for NI PXIe-4330

TB-RJ45-4330_Terminal_Block

The TB-RJ45-4330 is a front-mounting terminal block with RJ-45/RJ-50 terminal connectivity for the NI PXIe-4330 bridge input module.

NTCB-01 Connector Block                                                                  

Connector block is a matching module for input/output analog and digital signal and is used for connecting the data acquisition (DAQ) device to the external device.

NT-ROBO-7001 Universal Board                                                                  

The NT-ROBO-7001 universal board is intended to use with NI myRIO controller for using in wide range of areas like robotics applications, motors control, etc.

Ultrasonic Digital Signal Processing Board                        

ultrasonic_signal_generation_and_Processing_board

The board is dedicated for generation signal in ultrasound range and processing the reflected signal.

High voltage DC-DC Converter for Ultrasonic Applications                

High Voltage DC-DC Converter for Ultrasonic Applications

A boost-up DC-DC converter board has been designed and developed for ultrasound applications.